Is it best to go for a 1.6 petrol one than keeping the tdci until problems start arising, already Ive had to replace the fuel pump which had a broken seal and now Ive noticed the water is also dripping around the same area just further below the fuel pump from a silver metal pipe junction.

It seems the EGR valve on the 1.8 is part of the intake manifold so a much bigger job than the EGR valve clean/replacement on the 1.6. Seems a rather daft design to be honest but as I have never had a 1.8 I have never done one, quite expensive if it needs replacing, personally I would see about getting it cleaned and if it's faulty see about getting it mapped out.

Focus 1.8 tdci sport 5dr. Ford Year: 2006. Posted April 15, 2015. Have a 1.8 tech and its thrown out the codes to say issue with egr valve. Egr valve cleaner gone in and going to keep driving her any advice or idea on cost to replace. Quote.
Hi guys a few days ago my 1.4 Ford Fiesta tdci started to judder at idle it did this for a few days and then got worse and ended up with warning light and going in to limp mod I did a bit of searching and read that the egr valve mite be faulty so I replaced it with an new on and also a new fuel filter it’s still the same and keeps going into Focus 2011-2018 - How much is the EGR valve on the Ford Focus 1.6 TDCi 90 PS? Read Answer; Focus 2018-2025 - What problems with the EGR valve on the Ford Focus 1 6 tdci? Read Answer; Focus 2004-2011 - What to do in case of Ford Focus 1.6 TDCi EGR valve problems? Read Answer
Ford Focus 1.6 TDCI - Blanking EGR valve and fault codes - RT : If you've kept up with VW's issue in the USA and the much wider diesel issue in Europe affecting most, if not all, brands that sell diesel cars, then you'll be aware that NOx pollution is a major health issue - cars use the EGR to reduce NOx so it's inevitable that the authorities will take ALL possible steps to prevent tampering
This is a video of how to check and replace PCV valve on ford focus 1.6 TDCI and some of the engines of peugeot that are 1.6L Diesel.All rights reserved.This
When this happens the EGR valve will need to be replaced. With electric EGR valves, the problem could be an issue with the wiring. When your Ford Focus EGR valve fails, the check engine warning light will usually illuminate on the dash and the vehicle may run rough. The engine may run lean or rich, depending on why the valve has failed. Posted May 27, 2017. Morning. hope this is right place to post it. i have 2007 mk2 ford focus 1.6 tdci. and it have los of power. gives these codes on obd 2 reader. P0033 is the code for Turbocharger or Supercharger Bypass Valve Control Circuit. P0407 EGR Sensor B Circuit Low. P022B Charge Air Cooler Bypass Control A Circuit Low.

Ford Focus 1.6 tdci 2005 - EGR Valves problems and smoke - slkfanboy Grey/White smoke is pos. ERG needing cleaning could be a number of other issues, for example air leak in the intake system Grey/Blue is an oil issue can be hard to tell sometimes exact colour.

Ford Year: 2005. UK/Ireland Location: Please Select. Posted April 24, 2018. Hi. I have a engine light on my Ford Focus 2005, 1,6TDCi. I read the code (P1412) and it says "EGR valve frozen". I have tried dismounting and cleaning the valve, but the light comes back on after a while. I don't know what to do next, and i was wondering if changing
101. Name: James. Ford Model: MK7 1.6 TDCI Titanium 5 door. Ford Year: 2009. UK/Ireland Location: Lancashire. Posted April 21, 2013. Does anybody have a good guide to removing the egr valve. I've looked around on the Internet and can't find one. Even if its just a photo of it and the bolts that hold it on. EGR valve duty (%) Focus = 19.2 EGR valve duty (%) Volvo = 76 EGR valve position (%) Focus = 0 EGR valve position (%) Volvo = 100 Fuel rail pressure (psi) Focus = 3778 Fuel rail pressure (psi) Volvo = 4281 Everything else looks in order. The car won't accelerate properly and based on the above I'm now sure I should start with the APP position.

ayvo. so I've been looking at blanking/deleting the egr on my fiesta mk7 2009 1.6 tdci (non dpf 16 valve engine) instead of replacing it since its giving issues (keeps throwing a "egr stuck open code").. would the best way of doing this be putting a metal blanking plate between the egr (apparently this doesn't throw up an EML) and the engine or

sksSiTI.
  • scdty02klx.pages.dev/433
  • scdty02klx.pages.dev/409
  • scdty02klx.pages.dev/70
  • scdty02klx.pages.dev/385
  • scdty02klx.pages.dev/202
  • scdty02klx.pages.dev/83
  • scdty02klx.pages.dev/130
  • scdty02klx.pages.dev/79

    • ford focus 1.6 tdci egr valve problems